How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

You guys have been asking for this tutorial for ages (a whole year, to be exact), so I finally put my head down the last couple of weeks to get the project wrapped up and photographed, and now I’m finally ready to share the DIY details. It turns out that fixing dated decorative cabinet scrollwork is easier than you might think, so let’s dive into it.

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

First, let’s back up a little bit. As you may remember, the section of wood cabinetry above our kitchen sink has looked pretty dated since the day we moved in. This point was driven home with particular force when I took over the Better Homes & Gardens Instagram account early last year. Many of the first commenters on this particular photo took it upon themselves to bash the curvy scrollwork detail, calling it out as old fashioned and ugly. Of course, I didn’t disagree but would have loved nicer notice (you can read more about my thoughts on Internet bashing here).

Anyway, not one to really let that type of thing push me away from my own staunch home décor opinions, I left the scrollwork alone for several months. The project was still at the top of our to-do list, but it wasn’t something we rushed to cross off either since it wasn’t hurting anyone.

Then, an off-handed conversation with my dad about how we might eventually fix the dated header turned into a scheduled woodworking day. Practically nothing excites the two of us more than solving a home dilemma, so we put our heads together to come up with a simple process to update the woodwork with as little dust and debris as possible.

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

The ultimate goal was to keep the wood exactly as it is (because it’s just so beautiful!), but to remove the curvy edge to reveal a sleek straight line. This would help modernize the header just enough to not give away its age, and it would no longer draw the eye. I’d much rather place focus on the granite counters we splurged on.

To achieve that, the first thing we did was take a full-size level and lay it across the wood, end to end, just above the curvy edge. Using a black Sharpie, we marked out the line, and then used measuring tape to double check that the line was straight and an even distance from the crown moulding up top.

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

Next, we used a jig saw to cut carefully and slowly along the line. You can start your cut, like we did, by situating the blade along the bottom center of the wood header, pulling the trigger to get it going, and then slowly pushing the blade up at an angle into the wood until you reach the marked line. An alternative would be to drill a hole just below your marked line large enough to slip the jig saw blade through. Cut along the line with the jig saw in both directions, getting as close as you can to the cabinets on either side.

To finish the cuts without biting into the outer cabinets, we stopped our jig saw about a quarter of an inch from the cabinet edge, and then used a handheld jabsaw to finish the cut along the scrollwork. Then, it was just a matter of pulling the two loose end pieces off the nails that held them in place on the inside of the adjacent cabinets. A quick hammer wack on each nail loosened them enough to pull them out, finishing the first phase of the job.

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

Now, of course, we weren’t exactly done since the hacked header was looking a little jagged and uneven. To complete the project, we used a block plane to even out the raw edge as much as possible, and then my dad measured, cut, and stained a trim piece that covered both the raw edge on the bottom and the one on the front of the wood panel. You can get these types of L-shaped trim pieces at most home improvement stores if you’re not able to make your own. We pre-drilled pilot holes every 12 inches or so along the bottom of the trim piece, and then tapped nails into place to attach it to the wood header.

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

In a perfect world, we would have been able to access the hardware for the header so that we could have just taken it down and run it along a table saw (ultra flush nails prevented us from doing that), but the finishing trim method would still have come into play. Our custom process required a handful of extra steps, but, in the end, we were left with exactly the results we were hoping for: a super sleek, straight edge that allows the header to blend right in with the rest of the squared-off cabinetry.

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

How To Remove Decorative Cabinet Scrollwork

It’s amazing how such a small change can make such a big difference. We love the way the straight edge helps modernize our retro kitchen without taking away any of the gorgeous character. It looks a little crooked in these photos, but I assure you it’s perfect straight. So, what do you think of the update? Do you think you could manage the project on your own? I know you can! If you have any questions on the exact process or specific tools that we used, please don’t hesitate to leave a comment below.

Psssst…Future Carrie popping in! I just wanted to share an update that we’ve since removed the header (and cabinet to the right!) entirely to allow for maximum light, and you can see that update here.

How To Remove Decorative Cabinet Scrollwork

Add a comment...

Your email is never<\/em> published or shared. Required fields are marked *

getsocial

[instagram-feed feed=2]

have yousubscribed?
Everybody's doin' it.

[instagram-feed feed=1]